[time-nuts] Lucent RFTG-m-XO GPSDO

k4cle at aol.com k4cle at aol.com
Mon Oct 17 23:35:27 UTC 2011


All that's interested, KO4BB now has my RFTGm information on his manuals  
section under GPS Timing.  Please let me know if you have questions about  
it.  73's, Doug, K4CLE

Connected by DROID on Verizon Wireless

-----Original message-----
From: "Randy D. Hunt" <randy_hunt960 at yahoo.com>
To: Discussion of precise time and frequency measurement  
<time-nuts at febo.com>
Sent: Wed, Oct 12, 2011 16:53:04 GMT+00:00
Subject: Re: [time-nuts] Lucent RFTG-m-XO GPSDO

On 10/11/2011 6:28 PM, Peter Bell wrote:
> For some reason, the "No GPS" LED is back - although the GPS is
> tracking 8 satellites in 3D mode and according to the TRAIM status the
> timing error is below the alarm threshhold (alarm = 1300ns, current =
> 43ns) - I guess the uinit has it's own standards for the GPS quality,
> and they are being violated in some way.
>
> Still. at ;least I have seen it running with that LED off, which is a
> positve sign :)
>
>
> On Wed, Oct 12, 2011 at 5:42 AM, k4cle at aol.com<k4cle at aol.com>  wrote:
>> If I recall, the firmware in the RFTGm collects about an hours worth of  
position info and does an average to establish a self-survey.  The next time  
you cycle power, it will check the new position against the stored one and  
if within 50 feet or so, it will use the stored position.  That's probably  
why it took a while for the LED to extinguish.
>>
>> Connected by DROID on Verizon Wireless
>>
>> -----Original message-----
>> From: Peter Bell<bell.peter at gmail.com>
>> To: Discussion of precise time and frequency  
measurement<time-nuts at febo.com>
>> Sent: Tue, Oct 11, 2011 12:49:45 GMT+00:00
>> Subject: Re: [time-nuts] Lucent RFTG-m-XO GPSDO
>>
>> The Rx was defective - I just got the new one, hooked it up to my
>> little test rig anf the antenna, and it happily picked up satellites
>> and got a position fix.
>>
>> Swapped it into the box, and found a TTL level copy of the RX data
>> stream from the encore on pin 2 of the interface connector, so hooked
>> that up to a TTL->RS232 converter so I could monitor what was
>> happening.  It all seemed to be tracking OK, although the "No GPS" LED
>> was still on, so I just left it and after a couple of hours the LED
>> went out.
>>
>> Next step is getting the Rb working :)
>>
>>
>> On Mon, Oct 10, 2011 at 2:41 AM, k4cle at aol.com<k4cle at aol.com>  wrote:
>>> Hi Peter, yes it sounds like the UT+ is defective if it never gets any  
sats.  You can probably find one on eBay.  Someone probably fired RF into  
the receiver front-end and zapped it.  I think the antenna you are using  
should be OK.
>>>
>>> I will look for my drawings on this unit and send copies to you.  And I  
know I have the software too, just need to find it!
>>>
>>> I have read in some of the notes here on time-nuts that people may be  
able to use RS232 for communicating with the RFTG units.  But it was  
designed for RS422 and I would suggest you use RS422 for best results.  I  
use a little RS422-4S232 converter which has worked fine for me.
>>>
>>> The early units had FRS rubidiums in them.  The LPRO was used in the  
newer units.  So, you have the more recent design.
>>> Connected by DROID on Verizon Wireless
>>>
>>> -----Original message-----
>>> From: Peter Bell<bell.peter at gmail.com>
>>> To: Discussion of precise time and frequency  
measurement<time-nuts at febo.com>
>>> Sent: Sun, Oct 9, 2011 05:52:25 GMT+00:00
>>> Subject: Re: [time-nuts] Lucent RFTG-m-XO GPSDO
>>>
>>> On Sun, Oct 9, 2011 at 3:31 AM, k4cle at aol.com<k4cle at aol.com>  wrote:
>>>> Peter, do you have the software for this unit?  The GPS antenna is  
supposed
>>>> to draw apx. 20 mA at 5 volts in order for the NO GPS LED to turn off.   
AT&T
>>>> (Lucent) used the MicroPulse timing antenna (later sold and now  
provided by
>>>> PCTE).  You are correct in that Efratom used the Motorola UT+ 8 channel  
GPS
>>>> receiver on these units.  The rubidium companion box used the data from  
the
>>>> same receiver (via an interconnect cable between the two units).  Let  
me
>>>> know if you have questions on this unit, Regards, Doug....
>>>> Connected by DROID on Verizon Wireless
>>>>
>>>> -----Original message-----
>>>> From: Peter Bell<bell.peter at gmail.com>
>>>> To: time-nuts at febo.com
>>>> Sent: Fri, Oct 7, 2011 14:13:31 GMT+00:00
>>>> Subject: [time-nuts] Lucent RFTG-m-XO GPSDO
>>>>
>>>> I have been playing with one of these units, and noticed that there
>>>> has been some discussion on them before on this list, so I wondered if
>>>> anyone might have any suggestions.
>>>>
>>>> Basically, the unit powers up correctly, but the "No GPS" LED never
>>>> goes off - this obviously could be because it's broken or doesn't like
>>>> my antenna, but with some of these telecom GPSDOs you have to manually
>>>> trigger a site survey if you move them to another location. Does
>>>> anyone know if this Lucent box is like that?
>>>>
>>>> Everything else seems to be working - once the "OK" light comes on the
>>>> 15MHz output is enbled, the "No GPS" LED goes from solid to blinking
>>>> if you disconnect the antenna - it just doesn't want to get GPS lock.
>>>>
>>>> I suppose I could pull the Oncore board (a UT+ according to the label)
>>>> out of it and test that on it's own - but I thiought I would see if
>>>> maybe it's a known issue first.
>>>>
>>> Hi, Doug
>>>
>>> I don't have any documentation at all - just the actual box.  The
>>> antenna is one that originally came with a Furuno marine GPS, but the
>>> spec looks plausible (+5V @ 40mA, Internal L1 preamp with 26dB gain -
>>> and it has worked with several other GPS units without problems.
>>>
>>> I just pulled the oncore out, and connected it up outside the box -
>>> and it doesn't work.  It passes the self test with a response code of
>>> 0000 (or 8000 with the antenna disconnected / 4000 with a short on the
>>> antenna socket - so it seems the current consumption is OK) - but no
>>> matter how long you leave it it still says it's tracking 0 satellites,
>>> although it happiy generates status reports.
>>>
>>> I wonder if this UT+ version is expecially sensitive to the antenna?
>>> I remember that the oncore VP would work with pretty much anything you
>>> hooked up to it.  Of course, it's equally possible that the GPS module
>>> is defective.
>>>
>>> I'm tending towards broken - I also got an RTFG-m-RB with this unit,
>>> and that has a faulty LPRO-101 in it (it's probably fixable - it looks
>>> like the FET that heats up the Rb cell had gone open circuit) - and
>>> the two units together only cost me $40 supplied on a "status unkown,
>>> but likely defective" basis. I should get at least $40 of
>>> entertainment out of trying to fix them :)
>>>
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
The 'no gps light' on mine comes on periodically (usually around 
midnight) then goes off after a while.  My antenna is not in the best 
location, on window sill in corner.  But, for the most part, it stays 
off most of the time. . .

Randy
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to  
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.



More information about the time-nuts mailing list