[time-nuts] HP 105B Modification

francesco messineo francesco.messineo at gmail.com
Wed Dec 9 20:32:32 UTC 2009


Hello Bruce,

On 12/9/09, Bruce Griffiths <bruce.griffiths at xtra.co.nz> wrote:
> Francesco
>
>  Yes, just keep the gain of each stage low and cascade 2 or3 if you need
> higher reverse isolation.
>  Since the input impedance is around 1k (predominantly capacitive) at 10MHz
> you can drive several in parallel from a 50 ohm source.
>  If needed you can add a bridged T-coil network at the input to improve the
> broad band matching.
>

I would have one stage from the thunderbolt and then two cascaded
stages for each output all from the single first stage, would that
work? I'm not sure that for ordinary frequency distribution I need a
better level of isolation. I may be wrong of course.

>  If you need 100MHz operation just substitute a 4GHz ft transistor for the
> 2N5109/2N5943.

only 10 MHz!

>  In this case you may need to reduce the supply volatage dependent on the
> transistor ratings.
>
>  I've simulated cascades of 3 such amplifiers and found that the phase noise
> remains low.
>  The only thing to watch when cascading for improved isolation is reverse
> coupling via the common power supply.
>  However with well planned supply decoupling this won't be a problem.

ok, I got the hint :-)

>
>  The ft of the BC548/558 is only 300MHz compared to ~ 1GHz or so for the
> 2N5109/2N5943, so reverse isolation at high frequencies will be worse when
> you use the BC548/558.

as I said I just need this to work at precisely 10 MHz, and the
BC548/558 are a free (really) item here!
But maybe there could be a problem if one equipment puts back higher
frequency noise on its 10 MHz input? This could be solved by filtering
at each output?
Maybe one day I will use a similar stage to bring the IF signal out of
some of my amateur radio transceiver, but that's not something I plan
to do soon (I don't see the need for it currently) and in that case I
will use better transistors for sure.
Thanks
Francesco

>
>  Bruce
>
>  francesco messineo wrote:
>
> > Hi all,
> >
> > indeed this is very interesting, can this buffer amplifier be used as
> > a building block for a distribution amplifier for the 10 MHz signal of
> > a thunderbolt? I remember having seen on the list a similar version
> > but with european transistors (like the ubiquitous bc548/bc558?) that
> > are very common here, but I can't remember when it was to surf the
> > list archives in the right time-period. Anyone?
> > best regards
> >
> > Francesco IZ8DWF
> >
> > On 12/9/09, Ed Palmer<ed_palmer at sasktel.net>  wrote:
> >
> >
> > > I was thinking that I might be reinventing the wheel by designing a
> buffer
> > > amp.  You guys have almost built the entire car!  Thanks again for the
> > > ideas.  It'll take me a while to get it built and tested.
> > >
> > >  Ed
> > >
> > >  Bruce Griffiths wrote:
> > >
> > >
> > >
> > > > John Miles wrote:
> > > >
> > > >
> > > >
> > > > >
> > > > >
> > > > >
> > > > > >
> > > > > >
> > > > > > > If it helps I can send you some LTSpice schematics so that you
> can
> > > > > > > simulate the circuit for yourself.
> > > > > > > The breadboards behave as predicted by the simulations at 10MHz.
> > > > > > >
> > > > > > > John Miles has done some preliminary phase noise measurements on
> his
> > > > > > > version.
> > > > > > >
> > > > > > > The transformers are wound on binocular ferrite cores.
> > > > > > > I used some 14mm (long) cores intended for 40MHz to 220MHz (I
> had
> > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > > some)
> > >
> > >
> > > >
> > > > >
> > > > > >
> > > > > > > operation in my breadboard which works well at 5MHz and 10Mhz.
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > You can also use an off-the-shelf Mini-Circuits transformer for
> > > > > >
> > > > > >
> > > > >
> > > >
> > > low-power
> > >
> > >
> > > >
> > > > >
> > > > > > applications.  The T13-1 was the one I tried.  I'll stick some of
> > > > > > the plots
> > > > > > up on the web later tonight if possible.
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > See http://www.ke5fx.com/norton.htm for
> measurements
> > > > >
> > > > >
> > > >
> > > and connection details
> > >
> > >
> > > >
> > > > > of the copy of Bruce's amp that I added to my 5061A.
> > > > >
> > > > > -- john, KE5FX
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > Note the LED I used in the schematic was merely for simulation
> purposes
> > > >
> > > >
> > > (ie LTSpice had a model for it).
> > >
> > >
> > > > A standard red or amber LED is just fine.
> > > >
> > > > Another point is the LTSpice LED model isn't particularly accurate for
> > > >
> > > >
> > > simulating the effects of temperature variations.
> > >
> > >
> > > > Does anyone knows of more accurate LTSpice compatible LED models?
> > > >
> > > > The LED model voltage drop increases with temperature even at low
> current,
> > > >
> > > >
> > > whilst the voltage drop across a real LED at low currents decreases with
> > > temperature.
> > >
> > >
> > > > In practice the variation in the LED forward drop tracks the variation
> in
> > > >
> > > >
> > > the pnp Vbe quite well.
> > >
> > >
> > > > Bruce
> > > >
> > > >
> > > >
> > > >
> > >  _______________________________________________
> > >  time-nuts mailing list -- time-nuts at febo.com
> > >  To unsubscribe, go to
> > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > >  and follow the instructions there.
> > >
> > >
> > >
> > _______________________________________________
> > time-nuts mailing list -- time-nuts at febo.com
> > To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > and follow the instructions there.
> >
> >
> >
>
>
>
>  _______________________________________________
>  time-nuts mailing list -- time-nuts at febo.com
>  To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>  and follow the instructions there.
>



More information about the time-nuts mailing list