[time-nuts] 5061A Problem Child

J. L. Trantham jltran at att.net
Tue Jun 15 01:59:21 UTC 2010


Did that.  All day long Sunday.

Taking the evening off.

Joe

-----Original Message-----
From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
Behalf Of Robert Benward
Sent: Monday, June 14, 2010 8:49 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] 5061A Problem Child


Re-seat all of the boards several times.  Just to eliminate oxidation as a 
possible cause.

Bob


----- Original Message ----- 
From: "J. L. Trantham" <jltran at att.net>
To: "'Discussion of precise time and frequency measurement'" 
<time-nuts at febo.com>
Sent: Sunday, June 13, 2010 11:31 PM
Subject: Re: [time-nuts] 5061A Problem Child


> Corby,
>
> It has been a long and frustrating day.
>
> I swapped the A3, A8, A7, A14, and A1 assemblies with a functioning 
> unit
> and
> the assemblies from the 'problem child' worked in the 'good' unit and the
> assemblies from the 'good' unit failed to work in the 'problem child'.  I
> 'un-swapped the units and now my 'good' unit is having a problem starting 
> up
> the CS Oven.  I hope I have not created another problem.  I decided to let
> it run over night with CS Off and try again in the AM.
>
> The 'problem child' is behaving just like it is not being modulated.  
> I
> can
> not explain this unless there is some failure mode in the CS tube that 
> would
> allow Beam I to look ok but no 2nd Harmonic.  With Mod Off, there is a 
> nice
> single peak on Beam I as you adjust the Coarse Osc Frequency.  The 
> electron
> multiplier voltage on the tube is -1515 and I adjusted it to that voltage.
> Should it be more negative?
>
> The only thing measurable that is different from one unit to the other 
> is the absence of a signal on the A7J2 test point.
>
> The only other thing I can think of to do is to swap the tube with the 
> A4 assembly attached along with the A15 assembly from one unit to the 
> other and see what happens.
>
> Any thoughts?
>
> Thanks in advance.
>
> Joe
>
> -----Original Message-----
> From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] 
> On Behalf Of Corby Dawson
> Sent: Saturday, June 12, 2010 7:23 PM
> To: time-nuts at febo.com
> Subject: [time-nuts] 5061A Problem Child
>
>
> Joe,
>
> Try swapping the A8 module and see what happens.
>
> Corby ____________________________________________________________
> 2547% Penny Stock Picks?
> Our last pick exploded 2547% - Join our free newsletter today! 
> http://thirdpartyoffers.juno.com/TGL3141/4c1424f55b5b1597a6m04duc
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to 
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.


----------------------------------------------------------------------------
----



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.829 / Virus Database: 271.1.1/2931 - Release Date: 06/11/10 
02:35:00


_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.




More information about the time-nuts mailing list