[time-nuts] FS700 schematic
Ulrich Bangert
df6jb at ulrich-bangert.de
Tue Nov 23 17:52:13 UTC 2010
This: sours should of course read: source
> -----Ursprungliche Nachricht-----
> Von: time-nuts-bounces at febo.com
> [mailto:time-nuts-bounces at febo.com] Im Auftrag von Ulrich Bangert
> Gesendet: Dienstag, 23. November 2010 18:32
> An: 'Discussion of precise time and frequency measurement'
> Betreff: Re: [time-nuts] FS700 schematic
>
>
> Hi Paul,
>
> > If you are using something different then an active
> > antennathat draws current. You need a 470 ohm resistor to
> > ground at the antenna bnc.The system sense current being
> > drawn both high and low.
>
> Yes, this is understood. My "antenna coupler" for the W3
> includes a 560 Ohm resistor and Frank has found out that even
> a 1 K resistor is "accepted" as a functioning active antenna.
> My active loop draws some 8 mA from the center conductor and
> is therefore accepted as a functioning active antenna too.
>
> If the mysterious action has taken place it seems indeed as
> if the the receiver gain is set to a very low if not zero
> value. This is well understood because SRS says: If the <1 dB
> condition is met the receiver stops action, so setting the
> gain to zero or so may be a natural result of this. The big
> question is: What has happened before that makes the receiver
> THINK that this condition is met? Franks and mine receiver
> doing literally the same seems to indicate that the sours is
> the same for both of them.
>
> Best regards
> Ulrich Bangert
>
> > -----Ursprungliche Nachricht-----
> > Von: time-nuts-bounces at febo.com
> > [mailto:time-nuts-bounces at febo.com] Im Auftrag von paul swed
> > Gesendet: Montag, 22. November 2010 23:34
> > An: Discussion of precise time and frequency measurement
> > Betreff: Re: [time-nuts] FS700 schematic
> >
> >
> > Looked at the schematics front end is simple. Essentially op
> > amps notch filters and most important electronic selectable
> > attenuators. Any of it could cause issues. But the good news
> > is a amplified loran signal is on the back of the unit so you
> > could look to see whats happening to the signal. Oh other big
> > point. If you are using something different then an active
> > antennathat draws current. You need a 470 ohm resistor to
> > ground at the antenna bnc.The system sense current being
> > drawn both high and low. Regards Paul.
> >
> > On Mon, Nov 22, 2010 at 1:46 PM, paul swed
> > <paulswedb at gmail.com> wrote:
> >
> > > My thats a reasonable answer indeed.
> > >
> > >
> > > On Mon, Nov 22, 2010 at 12:24 PM, Stan, W1LE
> <stanw1le at verizon.net>
> > > wrote:
> > >
> > >> It is not just one page. What are you specifically
> looking for ?
> > >> Most sheets are B size ( double A size).
> > >>
> > >> I got the complete manual from SRS for ~35$
> > >>
> > >> Stan, W1LE
> > >>
> > >>
> > >>
> > >> On 11/22/2010 10:00 AM, Ulrich Bangert wrote:
> > >>
> > >>> Gentlemen,
> > >>>
> > >>> I know this one has been asked a few years before but I give it
> > >>> another
> > >>> try:
> > >>>
> > >>> Has anyone of you a Stanford Research FS700 schematic
> > available that
> > >>> he can share with me?
> > >>>
> > >>> Best regards
> > >>>
> > >>> Ulrich Bangert
> > >>> www.ulrich-bangert.de
> > >>> Ortholzer Weg 1
> > >>> 27243 Gross Ippener
> > >>>
> > >>>
> > >>> _______________________________________________
> > >>> time-nuts mailing list -- time-nuts at febo.com
> > >>> To unsubscribe, go to
> > >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > >>> and follow the instructions there.
> > >>>
> > >>>
> > >>
> > >> _______________________________________________
> > >> time-nuts mailing list -- time-nuts at febo.com
> > >> To unsubscribe, go to
> > >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > >> and follow the instructions there.
> > >>
> > >
> > >
> > _______________________________________________
> > time-nuts mailing list -- time-nuts at febo.com
> > To unsubscribe, go to
> > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > and follow the instructions there.
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the time-nuts
mailing list