[time-nuts] Different or defective FE-5680A?
Bob Camp
lists at rtty.us
Sat Jun 9 00:36:01 UTC 2012
HI
I suspect it's the same part then. I doubt they were using two vastly different Rb's on the same card.
Bob
On Jun 8, 2012, at 5:34 PM, Joseph Gray wrote:
> This one has no SMA and hasn't been modded in any way that I can tell.
> It came on a cutoff circuit board, like the others.
>
> Joe Gray
> W5JG
>
> On Fri, Jun 8, 2012 at 3:29 PM, Bob Camp <lists at rtty.us> wrote:
>> Hi
>>
>> There is a variant that comes from the factory with no 10 MHz output at all. Industrious people in far away places drill holes and wire up SMA connectors to give them a 10 MHz output. If yours is one of those, the mod may not have been 100% effective. Maybe a loose wire ….
>>
>> Bob
>>
>> On Jun 8, 2012, at 5:21 PM, Joseph Gray wrote:
>>
>>> Further information. I do get a Lock (low) indication on pin-3 and a
>>> PPS on pin-6. Nothing at all on pin-7.
>>>
>>> Joe Gray
>>> W5JG
>>>
>>> On Fri, Jun 8, 2012 at 1:41 PM, Joseph Gray <jgray at zianet.com> wrote:
>>>> Months ago, I ordered two FE-5680A units from nichgeek for my personal
>>>> use. They work just fine. Recently, I ordered one for work from the
>>>> same source.
>>>>
>>>> For the work unit, I ordered a small 15 VDC switcher and a 5 V DC-DC
>>>> module from Jameco. Today, I wired it all up, using the same pinout as
>>>> the previous units that I bought from nichegeek. Although the unit
>>>> gets warm, I get no 10 MHz output at all on pin 7.
>>>>
>>>> I double checked my wiring and it is OK. I even went home and got one
>>>> of my units. Plugging my home unit in place of the work unit, mine
>>>> puts out a nice 10 MHz in short order.
>>>>
>>>> Looking closer, I see that the two units are labeled differently. Mine
>>>> has a large white label that says "P/N 217400-30352-1". On the
>>>> smaller label "FE-5680A UN 78082" and "S/N 0434-84673". The work unit
>>>> is silkscreened with "PN: FE-5680A". The small label says "FE-5680A
>>>> UN37915 REVISION: B" and "S/N 0226-53954".
>>>>
>>>> I know that there are several versions of FE-5680A, with different
>>>> pinouts. I'm wondering if this latest unit is different than the two I
>>>> purchased before.
>>>>
>>>> I've emailed nichegeek and am awaiting a reply.
>>>>
>>>> Joe Gray
>>>> W5JG
>>>
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the time-nuts
mailing list