[time-nuts] Z3812 Diag port data? RE: time-nuts Digest, Vol 124, Issue 26
GandalfG8 at aol.com
GandalfG8 at aol.com
Mon Nov 3 05:22:00 EST 2014
Bob
It's possible that what you're seeing might well be normal operation when
they're operating as a pair, since Ref-0, what we've been calling the slave
because it has no GPS receiver, is actually the default "master" in
operational terms.
I only have Ref-1 units operating stand alone so perhaps someone else with
an operational pair can confirm whether or not any routine communication
exists with Ref-1 once the boot up sequence is finished?
In particular, when you say you can't communicate are you referring to the
J6 RS422/1PPS port, the J8 diagnostic port, or both?
A good test might be to set up your Ref-1 to operate stand alone.
Remove the interface cable and just fit two links to the Ref-1 J5
diagnostic connector, pin 2 to 8 and pin 3 to 13, and then power it up as normal.
It won't be outputting 15MHz and 1 PPS until the "fault" light goes off
and the "on" light is on, but you should be able to communicate with the J8
diagnostics port as soon as it's powered up.
I've used SatStat and other HP series Z3xx compatible software and all
worked fine, and that should continue after the boot up period ends and the
outputs are enabled.
I haven't so far tried the J6 RS422 port with the Lucent software as I've
been more interested in the GPS side of things and didn't want to dig into
the box itself before I've had time to study the RFTG-m manual re the
software commands and better understand the implications.
Regards
Nigel
GM8PZR
In a message dated 03/11/2014 03:16:35 GMT Standard Time, bob at evoria.net
writes:
Hi Bob,
I am only able to communicate with my system through the REF-0/slave unit.
I had thought this was normal behavior till someone, you perhaps, posted
that that was not correct. So, I've emailed Aecis to request a replacement
REF-1.
Bob From: Bob Camp <kb8tq at n1k.org>
To: Discussion of precise time and frequency measurement
<time-nuts at febo.com>
Sent: Sunday, November 2, 2014 8:20 PM
Subject: Re: [time-nuts] Z3812 Diag port data? RE: time-nuts Digest, Vol
124, Issue 26
HI
So at least there is one way communications from the GPS box to the slave
box.
Bidirectional com would be a bit complex given the lack of UART’s on the
pc board. I’d bet it just runs through a standard set of messages on the GPS
and watches the results. The way to quickly prove I’m wrong would be to
issue a command to the GPS from the slave that it must respond to. Something
like go into survey mode or set the location to xxx yyy zzz. I’ve
certainly been wrong before.
I suppose they could do dual source TTL com directly at the GPS module
level. I’d think that would drive the GPS unit a bit nuts when the slave
started switching things around….
Bob
> On Nov 2, 2014, at 4:16 PM, n2lym <n2lym at optonline.net> wrote:
>
> Yes the diagnostic port on the slave unit diaplay's gps data just like
the Z3811. Therefore there must be serial data being exchanged on the 15 pin
interconnect.
>
>
> Mike
>
> N2LYM
>
>
>
>
>
> Message: 5
> Date: Sun, 2 Nov 2014 15:58:20 -0500
> From: GandalfG8 at aol.com
> To: time-nuts at febo.com
> Subject: Re: [time-nuts] Lucent KS-24361, HP/Symmetricom Z3809A,
> Z3810A, Z3811A, Z3812...
> Message-ID: <868c5.58494d20.4187f4ec at aol.com>
> Content-Type: text/plain; charset="UTF-8"
>
> Just another thought though, does the diagnostic port on the slave also
> communicate with SatStat etc?
>
> That would imply at least a transfer of serial data in one direction,
even
> if not for the control functions.
>
> Regards
>
> Nigel
> GM8PZR
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to htt
ps://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
More information about the time-nuts
mailing list