[time-nuts] GPS receiver weirdness

Chris Dawes cdawes at scientific-devices.com.au
Thu Mar 10 15:01:14 EST 2016


Sean,

I am a Microsemi rep, are they bc635 or 637 cards, if the latter this may be the issue see attached

Best regards
Chris Dawes
Scientific Devices Aust
0409 154 684
www.scientific-devices.com.au 


-----Original Message-----
From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of Sean Gallagher
Sent: Friday, 11 March 2016 2:16 AM
To: time-nuts at febo.com
Subject: [time-nuts] GPS receiver weirdness

Good morning time-nuts,

I just sent this email to Olivier who was our contact over in France with Heol Designs. They made the replacement board with the same form as the Trimble Ace III that would work with our buggy TS2100 machines and I have recently run into problems and I wanted to share this with you all. 
Forgive me for the length I was really just doing a brain dump of everything I've noticed so far:

"
Hi Olivier,

Okay, so I  spent all day yesterday testing out various things with one of my interns. This is a bit confusing to follow even when I was trying to explain it in person to my boss, so if you have any questions just let me know.

We have two TS2100 machines. One is from Datum and the other is slightly newer from Symmetricom (Who bought Datum and is now owned by Microsemi). 
We were using the Datum 2100 for the testing purposes since it happened to be the one plugged in but they are both running v4.1 firmware. I also just hooked up the newer one and plugged in your receiver to it with the same results which I'll explain in a second.

Besides the two operational servers with the bc635PCI cards in them we have a couple extra servers and about 20 spare 635 cards. I have the spare servers off to the side and disconnected from the production environment. They are there for testing purposes for things like this, and we are trying to upgrade software too.

We purchased  3 N024 receivers from you and had one in the hooked-up 2100, and one each in my two operational servers attached to the 635 frequency processors.

I should mention that we currently have what we are thinking of as 4 "generations" of GPS receivers. Besides yours, which we know is the newest, we are basing these generations mostly on the appearance of the cards as there are no dates or anything on them. Things like the size of the components and the "shininess" of the cards.
Gen 1: I only have one of these and I think it came out of the oldest
2100 but I'm not 100% sure because I can't remember.
Gen 2: I have a few of these. One was in the newer 2100, and others were on 635 cards and laying around Gen 3: Shinier and newer looking. I have a few of these as well Gen 4: The Heol design cards.

Generation 1-3 cards all had the rollover issue a few months ago that caused us to purchase the units from you.

This is where things start to get weird.... A couple of weeks ago I went to switch some things around and have my 2100 output timecode into one of my production servers. When I did it and went to audit the server against the second server (still running GPS) it failed because the time was 1 second fast. This was when I first noticed something was wrong. It may have been like this earlier but since we weren't really using the
2100 I hadn't looked closely at it.

This led to yesterday and me trying all of the GPS receivers I have in the 2100, and also trying them in my test environment too with 635 cards. Results when compared to nist.gov and the GPS time displaying on the monitors for my servers were:

TS2100
      Gen 1 card: Time and date are correct, the UTC offset of the card is +17
      Gen 2: Time and date are correct, UTC offset is +17 (we did have one that failed to ever get time)
      Gen 3: Time and date are correct, UTC offset is +17
      Gen 4 (Heol): Date is correct, time is +1 second fast, UTC offset is +20

bc635PCI frequency processor cards
      This is a little more difficult because I currently cannot get ANY of my receivers (Gen1-4) to work with any 635 cards in my test environment. For the most part it looks like the 635 is recognizing that a GPS card is hooked up but it's not translating any data.

I can say in the two production servers that each have one of the Heol cards hooked up to a 635 card that the time and date are both correct, and the UTC offset is still +20.


The actual UTC offset is currently +17 since the leap event a few months ago. So needless to say I am thoroughly confused as it looks like nothing should be working on paper at this point but somehow is.

And I'm not sure if the 635 cards have run into some kind of end of life issue that is causing them to not work with GPS anymore, and the only reason my 2 production servers work still is because they haven't been powered off or some other issue....
"

Respectfully,

Sean Gallagher
Malware Analyst
571-340-3475
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
--
Message  protected by MailGuard: e-mail anti-virus, anti-spam and content filtering.
http://www.mailguard.com.au


-------------- next part --------------
A non-text attachment was scrubbed...
Name: FSB 098-50620-83.pdf
Type: application/pdf
Size: 30876 bytes
Desc: FSB 098-50620-83.pdf
URL: <http://www.febo.com/pipermail/time-nuts/attachments/20160310/79a52f03/attachment.pdf>


More information about the time-nuts mailing list