[time-nuts] high rev isolation amps

Rob Sherwood. rob at nc0b.com
Sat Mar 26 20:34:21 EDT 2016


I use two ZHL-32A buffer amps, the appropriate Mini-Circuits LPFs, and 20 dB pads into a 4-way Mini-Circuits combiner. I believe it is ports 2&3 that have even better isolation than a 2-way combiner.  These buffer amps run on 24 volts, where the ZFL-500LN doesn't have the output capability to test 100+ dB radios.  Some tests need a third signal source and complimentary buffer amp and associated items. 

To test a K3S or an IC-7851, it also requires HP 8642A generators that have lower phase noise than these top of the line rigs.  Even my 8662A generators are not good enough, though they were 5 years ago.  Now add the Flex 6700 and the ANAN-200D, the RMDR performance of a hand full of rigs is amazing. 

Unfortunately transmitter performance has not kept pace with receiver improvement. 

It will be interesting to test the new IC-7300 DSR with knobs (and lots of menus). 

Rob
NC0B

Sent from my iPad

> On Mar 26, 2016, at 6:00 PM, "jimlux" <jimlux at earthlink.net> wrote:
> 
> 
> 
>> On 3/26/16 2:30 PM, Rob Sherwood. wrote:
>> You cannot add the directivity and gain.  Doesn't work that way.  Rob, NC0B.
>> 
> 
> Yeah, I kind of figured that after getting the S parameters from minicircuits.
> 
>> Sent from my iPad
>> 
>>> On Mar 26, 2016, at 2:00 PM, "jimlux" <jimlux at earthlink.net> wrote:
>>> 
>>> 
>>> 
>>> Consulting the time-nuts hive mind here..
>>> 
>>> I'm looking for off the shelf connectorized amplifiers with very good reverse isolation for doing things like intermod measurements (e.g. 2 signal generators followed by amps/pads into a combiner) and phase noise measurements for a digital receiver.
>>> 
>>> 1-100 MHz kind of frequency range..
>>> 
>>> I've used ZFL-500LN (30dB gain, 27 dB directivity in the data sheet, which I interpret as 57dB reverse) , ZX60-4016 (really more of a microwave amp, and not so hot reverse wise.. 25 dB)
>>> 
>>> I'm not particularly cost constrained, so a higher power amp (which also reduces distortion products from the amp) followed by pads is always an alternative.
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>> 
>>> 
>>> 
>>> --
>>> If this email is spam, report it to
>>> https://support.onlymyemail.com/view/report_spam/ODExMjI6MTg2NjQ0MTI4Mjpyb2JAbmMwYi5jb206ZGVsaXZlcmVk
>>> 
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>> 
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> 
> 
> 
> --
> If this email is spam, report it to
> https://support.onlymyemail.com/view/report_spam/ODExMjI6MTg2NjQ2NDY5Nzpyb2JAbmMwYi5jb206ZGVsaXZlcmVk
> 


More information about the time-nuts mailing list