[time-nuts] General questions about making measurements with time interval counter.
Bob Camp
kb8tq at n1k.org
Thu Jan 12 15:38:30 EST 2017
Hi
Keep in mind that when you do 1800 samples at 1 second, that data will only meet the
100 sample requirement out to tau = 18 seconds. Past that you are in the “under 100 samples
region”.
Bob
> On Jan 12, 2017, at 2:32 PM, Bob Stewart <bob at evoria.net> wrote:
>
> Hi Bob,
> OK, thanks for explaining. When you and others use highly technical terms like "small number of samples" it's not always clear to me what you mean. =) Ten samples? That's not enough for anything. Normally I run at least 1800 samples; at least if I plan to share them with someone.
>
> Bob -----------------------------------------------------------------
> AE6RV.com
>
> GFS GPSDO list:
> groups.yahoo.com/neo/groups/GFS-GPSDOs/info
>
> From: Bob Camp <kb8tq at n1k.org>
> To: Bob Stewart <bob at evoria.net>; Discussion of precise time and frequency measurement <time-nuts at febo.com>
> Sent: Thursday, January 12, 2017 1:03 PM
> Subject: Re: [time-nuts] General questions about making measurements with time interval counter.
>
> Hi
>
> It varies from 5370 to 5370. You see a lot of plots that run out to 10 samples or less. Anything below 100 samples
> is risky in some senses.
>
> Bob
>
>> On Jan 12, 2017, at 12:25 PM, Bob Stewart <bob at evoria.net> wrote:
>>
>> Hi Bob,
>> OK, what's a small number of data points? Attached is a screencap of captures for 25, 50, 75, 100, and 150 seconds. Yeah, at 25 seconds, the 1S tau is up at 4.56E-11, but it falls pretty quickly. I will mention that this particular 5370 is much better than my other one. So, maybe this one is an exceptional example?
>>
>> Just for grins, I also included a screencap of the phase points.
>>
>> Bob -----------------------------------------------------------------
>> AE6RV.com
>>
>> GFS GPSDO list:
>> groups.yahoo.com/neo/groups/GFS-GPSDOs/info
>>
>> From: Bob Camp <kb8tq at n1k.org>
>> To: Bob Stewart <bob at evoria.net>; Discussion of precise time and frequency measurement <time-nuts at febo.com>
>> Sent: Thursday, January 12, 2017 11:04 AM
>> Subject: Re: [time-nuts] General questions about making measurements with time interval counter.
>>
>> Hi
>>
>> There is a big difference between RMS and single shot. Single shot, the 5370 is a very different beast.
>> That’s not a big deal when you have a few thousand readings and it all averages down. Unfortunately
>> we all love to do runs with a very small number of points and then draw conclusions from them. As the
>> sample size goes down, you no longer have a 2 to 4 x 10^-11 beast, it’s more like 5X that.
>>
>> Bob
>>
>>
>>> On Jan 12, 2017, at 11:31 AM, Bob Stewart <bob at evoria.net> wrote:
>>>
>>> Hi Bob,
>>> Normally I see somewhere between 2E-11 and 4E-11 at 1S tau on my 5370A, as in the blue trace on the attached plot. Am I misunderstanding your meaning? Granted, I am clocking the 5370A with a GPSDO, but I believe I see about the same thing with the HP10811. This test was 1PPS vs 1PPS on two different units.
>>> The plot also has a test run by Tom, in orange, using his H Maser and a Timepod to show how poor the 5370 is compared to the Timepod below about 60S tau. These are essentially apples vs apples tests.
>>>
>>> Bob
>>>
>>>
>>>
>>>
>>> From: Bob Camp <kb8tq at n1k.org>
>>> To: Discussion of precise time and frequency measurement <time-nuts at febo.com>
>>> Sent: Thursday, January 12, 2017 8:27 AM
>>> Subject: Re: [time-nuts] General questions about making measurements with time interval counter.
>>>
>>> Hi
>>>
>>> There are a number of ways to improve the resolution (and accuracy) of your data without spending
>>> big piles of cash. They have been discussed here on the list many times over the last few years.
>>> What I’m suggesting is that you dig into that ahead of taking data. You will dive into it eventually as you
>>> look more and more at devices that are locked to some sort of stable reference internally.
>>>
>>> Ideally you would like a device with a floor 5X to 10X better than what you are measuring. For ADEV style
>>> data, the 5370 is a 1x10^-10 sort of device single shot (so 1x10^-9 is the limit at 10:1). With a lot of averaging
>>> (which is not something you do with ADEV) you can get about 5X better than that as a floor. In either case, it is getting in the way of any
>>> readings that are much below 1x10^-9 at one second. A low cost XO can hit that level of performance.
>>>
>>> Bob
>>>
>>>
>>> <ADEV.png>_______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>
>>
>> <ADEVs.png><Phase.png>_______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the time-nuts
mailing list