[volt-nuts] Basic question concerning voltage references

Jerry Hancock jerry at hanler.com
Mon Feb 20 15:53:32 EST 2017


You can get 7.5 digits using the HIRES register over GPIB or by using the stat function from the front panel.


> On Feb 20, 2017, at 11:33 AM, Tom Miller <tmiller11147 at verizon.net> wrote:
> 
> I believe you can get 7-1/2 digits out of the 3457A via the HPIB port.
> 
> Regards,
> Tom
> 
> ----- Original Message ----- From: "Russ Ramirez" <russ.ramirez at gmail.com>
> To: "Discussion of precise voltage measurement" <volt-nuts at febo.com>
> Sent: Monday, February 20, 2017 2:26 PM
> Subject: Re: [volt-nuts] Basic question concerning voltage references
> 
> 
>> My question is partly based on a real situation where I have 3 DMMs of
>> decent quality Keithley 2000, 34970A (34401A), and 3457A that all agree
>> with a good quality voltage reference that is exceeding its ppm/degree C
>> spec as far as I am able to tell. I felt that this was telling me that I
>> would need a 3458A to know how much closer to 10V the reference was at this
>> point. A quick calculation of 20 bits of ADC for example told me that I was
>> looking at 9.5 uV of resolution, or 0.6 uV at 24 bits *noise free*, etc. so
>> it did not seem to be entirely unreasonable to see the LSD of a 6 1/2 digit
>> DMM be higher than 1 or 2 counts.
>> 
>> Russ
>> 
>> On Mon, Feb 20, 2017 at 12:57 PM, m k <m1k3k1 at hotmail.com> wrote:
>> 
>>> On 20/02/2017 18:46, Russ Ramirez wrote:
>>> > I very much enjoy what is shared here. It has led me down the path of
>>> > learning more about Metrology in general and the pointers to Flukecal
>>> site
>>> > from here are appreciated.
>>> >
>>> > My question is this. If I measured a 10 volt reference known to be good
>>> to
>>> > 8 1/2 digits, but with the LSD being > 0, assuming a transfer standard
>>> with
>>> > traceability and documented uncertainties etc, would a 6 1/2 digit
>>> > voltmeter read 10.00000 volts, or round up to the limits of its AD
>>> > converter resolution; say X uV over 10.00000 volts?
>>> >
>>> > I hope this is not too basic a question.
>>> >
>>> > Russ
>>> > _______________________________________________
>>> >
>>> Hi Russ,
>>> 
>>> some voltmeters will supply extra digits in the output they provide, but
>>> whether they are of any use depends upon how
>>> stable the reference is in that particular 6.5 digit dvm, unfortunately it
>>> needs a dvm with better capability to prove
>>> if those digits are believable.
>>> 
>>> 
>>> _______________________________________________
>>> volt-nuts mailing list -- volt-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/
>>> mailman/listinfo/volt-nuts
>>> and follow the instructions there.
>>> 
>> _______________________________________________
>> volt-nuts mailing list -- volt-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts
>> and follow the instructions there. 
> 
> _______________________________________________
> volt-nuts mailing list -- volt-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts
> and follow the instructions there.



More information about the volt-nuts mailing list