[time-nuts] Fw: 5065

Mark Spencer mark at alignedsolutions.com
Sat Mar 19 10:09:53 EDT 2016


For those of us in Western Canada, I've purchased circular connectors at MRO electronics.

Best regards
Mark Spencer

Sent from my iPhone

> On Mar 17, 2016, at 9:29 PM, Clay Autery <cautery at montac.com> wrote:
> 
> Also Allied Electronics...  If I knew it was CPCs y'all were talking
> about...  same stuff we used in aviation, et al. for comms, nav aids, etc...
> 
> Also used in the oilfield for some equipment cables for data acquisition.
> 
> Plug:  https://www.alliedelec.com/te-connectivity-213905-1/70082887/
> Receptacle: https://www.alliedelec.com/te-connectivity-213889-2/70082884/
> 
> Pins, et al. are also available; look at the bottom of the pages...
> 
> If you can't find the exact 3 position plug/receptacle, you can always
> use a 4, 5, 6, etc... and simply plug the holes you aren't using...
> 
> ______________________
> Clay Autery, KG5LKV
> MONTAC Enterprises
> (318) 518-1389
> 
>> On 3/17/2016 4:56 PM, J. L. Trantham wrote:
>> Ulrich,
>> 
>> The connectors can be obtained reasonably inexpensively from Galco.  
>> 
>> http://www.galco.com/shop/Circular-Connectors
>> 
>> They are a 3 pin circular connector, consisting of three parts, that are purchased as an 'insert', 'shell', and 'clamp', IIRC.  I don't have the part numbers in front of me but they are the same for the 5061 Cesium standards.
>> 
>> I can get you the specific part numbers if you can't find it in the archives.
>> 
>> I used a spare 3 wire extension cord and just cut the end off the cord and installed the connector to mate with the 5065A and 5061A.  I've been told that the wiring is different between the 5061A and some of the 5065A's but I've never found a 5065A that was different from my 5061A.
>> 
>> Might want to open the unit and make sure the wiring matches the schematic.
>> 
>> Good luck.
>> 
>> Joe
>> 
>> -----Original Message-----
>> From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of KA2WEU--- via time-nuts
>> Sent: Thursday, March 17, 2016 9:30 AM
>> To: time-nuts at febo.com
>> Subject: Re: [time-nuts] Fw: 5065
>> 
>> 
>> The HP 5065A Rubidium Frequency Standard requires  a circular 3 pin adapter cable that  can be plugged into 115V AC outlet. 
>> I checked all cables I have  and this particular cable  is not finable. Can the unit set to 110/220 V  
>> Maybe  this cable can be  purchased  or assembled ?   ULRICH  
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>> 
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> 


More information about the time-nuts mailing list