[time-nuts] SSR-6t Connector

paul swed paulswedb at gmail.com
Thu Dec 20 15:53:59 UTC 2012


Understood that its 3.3 yup need some regulators but I am hoping I can
essentially drop the ssr into the 3801.
Thanks

On Thu, Dec 20, 2012 at 10:48 AM, dlewis6767 <dlewis6767 at austin.rr.com>wrote:

> The SSR-6t is a 3.3v device.
>
>
>
>
>
>
> ------------------------------**--------------------
> From: "paul swed" <paulswedb at gmail.com>
> Sent: Thursday, December 20, 2012 9:41 AM
> To: "Discussion of precise time and frequency measurement" <
> time-nuts at febo.com>
> Subject: Re: [time-nuts] SSR-6t Connector
>
>
>  Not to hijack the thread. I purchased a ssr and have not rcvd it yet. But
>> my simple interest is to if needed replace the rcvr in my z3801. There
>> have
>> been threads on time-nuts that these rcvrs do fail with age.
>> My belief is that though the connector on the 3801 may be different and it
>> is 5V, essentially connecting the 1 pps TX RX data and power should allow
>> this to replace the older rcvr.
>> Am I on the right track?
>> As a longer term goal and question does this new rcvr actually improve a
>> 3801s stability?
>> Thanks
>> Paul
>> WB8TSL
>>
>> On Thu, Dec 20, 2012 at 10:16 AM, David Martin <
>> drmartin at ivietechnologies.com> wrote:
>>
>>  I had a Motorola M12+ all hooked up with a RF pigtail and data header so
>>> I
>>> just unplugged the Motorola and plugged in the SSR-6t.
>>>
>>> The data connector was purchased from digikey several years ago and the
>>> details have been lost in the dust.
>>>
>>> However it looks like
>>>
>>> http://search.digikey.com/**scripts/DkSearch/dksus.dll?**
>>> Detail&name=A33546-ND<http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=A33546-ND>
>>>
>>> I'm unhappy with the one I'm using as the contacts spring pressure is
>>> weak
>>> against the connector pin -- I will have to consider looking for a more
>>> "firm" fitting data connector.
>>>
>>> The RF pigtail was also obtained years ago from data-alliance.net -
>>> their
>>> P3B adapter cable.
>>>
>>> See
>>>
>>> http://www.data-alliance.net/**servlet/-strse-800/MCX-BNC-**
>>> female-Adapter/Detail<http://www.data-alliance.net/servlet/-strse-800/MCX-BNC-female-Adapter/Detail>
>>>
>>> - Sent from my iPhone -
>>> Please Reply To
>>> David Martin
>>> drmartin at ivietechnologies.com
>>> 801-372-0978
>>>
>>> Just curious,
>>> what connector/pigtail/adapter board did you use to access the 2x5 1.27mm
>>> pitch connector on your SSR-6T.
>>> Thanks,
>>> Dale NV8U
>>> ______________________________**_________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to
>>> https://www.febo.com/cgi-bin/**mailman/listinfo/time-nuts<https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts>
>>> and follow the instructions there.
>>>
>>>  ______________________________**_________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/**
>> mailman/listinfo/time-nuts<https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts>
>> and follow the instructions there.
>>
>
>
> ______________________________**_________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/**
> mailman/listinfo/time-nuts<https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts>
> and follow the instructions there.
>


More information about the time-nuts mailing list